THE OFFICIAL INTAKE THREAD!!

[DISIindahead]

Updated 2/2015 by @Inquisitive;! Thank you!

**********THE OFFICIAL INTAKE/ TURBO INLET PIPE THREAD**********

NOTE: This is an informative discussion and a resource for gathering information on which route to go (Short Ram Intake, Cold Air Intake). All-in-all it is up to you on which you decide to go with.

Abbreviations used on this sticky:

Gen1 MS3---> Mazdaspeed 3: 2006-2009
Gen2 MS3---> Mazdaspeed 3: 2010+

Difference between SRI and CAI: According to research and discussions there are inherent pros and cons of both intake systems, but the main difference between a short ram intake and a cold air intake is where the intake gets its air from. A short ram intake sits and the engine bay where the air temps are warmer due to the heat the engine produces while a cold air intake sits away from the engine bay, usually in the front fender where it can suck in cooler air from the outside. Sucking in cool air is important because cool air is denser than warm air, which means cool air molecules are closer together, so more air can fit into a given amount of space. An engine creates power by mixing and compressing air and fuel. The more air you can fit into a cylinder at one time, the bigger explosion you can create which in turn creates more horsepower.

NOTE: I've decided to list the filter covers first because I noticed that people have expressed concerns about water penetrating their engines with the cold air intake systems. First, it is HIGHLY unlikely that this will ever be a problem. Rain and water droplets are no problem. The only case that could be a potential threat is if you drove into an extremely deep puddle, submerging the intake head. The car would have to be in the water so that the intake was submerged, and then it would start sucking up water, making your engine hydro-lock.

Intake Kits and Battery Trays

Intake Kits: SRI, TIP, CAI
Battery Trays to accommodate wide Intake Kits

++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++++++++++++++++++++++++++++++++++

Intake Kits: SRI, TIP, CAI

CAI

Cold air is denser than hot air, and will ultimately have more power producing potential. Cold air induction (CAI) provides colder air than SRI / TIPs and can provide 12% more power and torque, but experiences pressure drops associated with the longer tubes used and are prone to easily hydro-locking in deep puddles (MSF wiki). Therefore, SRI / TIPs with air-box are the preferred option. Use a filter cover (CP-E, Outerwears. AMSoil) and / or splash shield (CP-E, Sure) if you are concerned about rain and water droplets, but they will not prevent hydro-lock if your intake is submerged.

SRI / TIP

Points to consider when improving the intake airflow are the future needs, such as BT for the K04 will most likely fail at some point. Although some members progress through different BTs, perhaps choosing a three inch intake initially will prevent having to replace it again later. The only problem with this course of action is that a MAF calibration must be done, which requires an ECU re-flash. See the “Larger than stock MAF housing” calculation below installation time in this section.

TIPs can flow 14% more, but are usually limited by the SRI. The main advantages to TIPs are the reduction of backwash turbulences away from the MAF housing from the blow-by valve and PCV.

However, SRI / TIPs allow the turbo to spike more easily. (Cobb) Note that with no other changes, tilting the MAF more than the OEM 15 degrees causes over fuelling with the ECU removing fuel through large negative LTFT and you exceed your previous g/s readings during WOT. MAF recalibration is strongly recommended.

Larger than stock MAF housing offers larger cross section for more airflow, but has less cooling to the MAF resistors due to the decreased air velocity. In order to develop a scalar for a larger than stock intake diameter, you must take the (New MAF Cross-Sectional Area) and divide (/) it by the (Stock MAF Cross Sectional Area), which is technically pi * radius squared (Djuosnteisn), but you can actually just take the new diameter squared / old diameter squared (ms3blackmica). Say you decide to upgrade to a 3" intake (76.2mm). The stock MAF housing is 66.5mm diameter (2.61811").

(76.2^2) / (66.5^2) = 1.313

Take 1.313 and multiply it by the entire MAF curve. Now you are ready to start your MAF Calibration. This is only an example for a 3" intake. (ms3blackmica)

CorkSport TIP

Power Series III 3” SRI / TIP with velocity stack and AEM dry air filter: “impressive improvement in power” with 35% more air flow; CorkSport Stage II Power Series SRI / TIP; 33 more HP and 25 lbs more torque from 14% more airflow with billet aluminium air straightener to prevent air leaks and CELs from inaccurate readings and dry air filter; CorkSport Power Series I SRI: 12 more HP, 17 more lbs torque with air straightener and dry air filter; relocated valve cover breather tube to prevent Genwon smoking turbo (rfinkle2).
Available from: CorkSport TIP
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $115.99 Standard Vent Breather Hose or Mazda Service Bulletin Fix 01-002/11; Polished or Powder Coated Black; Black, Red or Blue Silicone; Polished or Black Clamps

CorkSport SRI

Available from:
MS6
CorkSport SRI MS6
MS3
CorkSport SRI MS3
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $179.99 Black, Red, Blue or White Silicon Tubing; Black, Red (+$5) or Blue MAF (+$5); Blue, Red or Black Filter, Polished or Black Clamp

HTP 3" TIP

T6061, black powder coat, recirculation hose delete option with BOV, reducer size options, some require optional smaller HTP battery tray
Available from: HTP 3" TIP
MS6 (Yes), MS3 Gen1 (Yes) and Gen2 (Yes) $125 polished ($140 for black powder coated version) + optional: mounting bracket $10 + couplers $0 to $5 (2”, 2.25”, 3”, 4”), VTA $10, elbow $0 to $24 + shipping

Cobb SRI
MS6

MS3

11 HP gain, 16 lb-ft gain, removes pre-turbo restriction, optimises flow, minimizes turbulence, velocity stack, air flow straightener, conical cloth air filter, possibly CARB certified, reduces heat transfer; Cobb Turbo Inlet Hose: taper design to smooth airflow, silicone rejects high engine bay temperatures; steel wire reinforced to prevent collapsing. RMM replacement is recommended to avoid breaking the intake bracket.
Available from:
MS6
Cobb SRI MS6
MS3
Cobb SRI MS3
MS6 (Yes) $150, MS3 Gen1 (Yes), MS3 Gen2 (Yes) $195

Cobb TIP

Available from: Cobb TIP
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $180

James Barone Racing (JBR) DISI TIP

(Stage I SRI, Stage II SRI / TIP, Stage III CAI) or Wide Path (3” tube 59% up to 3.5” 41% for 4” turbo inlet, but then requires a small battery box (JBR 51R) (Black, Blue, Red, White); or stock 2.25” turbo inlet) 5-ply, wire reinforced silicon. The TIP reduces turbulence seen in the OEM factory accordion rubber hose version and can flow to 300 g/s on stock K04 turbo. SS T-Bolt Clamps, plug to run in non-recirc mode; James Barone Racing (JBR) Filter: soap and water washable dry filter (avoids over oiling) can flow 200% more air than OEM while providing superior engine protection capable of removing extremely fine particles down to < 0.1 micron; developed with K&N (similar to CorkSport and Cobb)
Available from:
MS6
JBR TIP MS6
MS3
JBR TIP MS3
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $165 Silicone: Black, Blue, Red

JBR SRI

Available from:
MS6
JBR SRI MS6
MS3
JBR SRI MS3
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $170 MAF / Filter: Black, Blue, Red; Silicone: adds White

JBR Dry Filter Wrap

Available from: JBR Dry Filter Wrap
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $25 Black, Red, Blue

JBR Tru-3.0 Wide Path Full Aluminium / Silicone Intake
Aluminium

Silicone

Available from:
Aluminium
JBR Tru-3.0 Wide Path Full Aluminium Intake
Silicone
JBR Tru-3.0 Wide Path Full Silicone Intake
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $285 TIP: 2.25” Stock, 2.5” BNR, 3” (aluminium only), 4” GT; Silicone: Red, Blue, Black, White; Filter: Blue, Red or Black

HTP 3.5" Full Intake

Available from: HTP 3.5" Full Intake
MS6 (Yes) $414.75 for 51R battery or $435.70 small battery, MS3 Gen1 (Yes), MS3 Gen2 (Yes) $275 stock battery or $432.92 for 51R battery; Coupler: 2.25”, 2.5”, 3”, 3.5”; Air Straightener included; VTA $10; Pre-Filter $30; Air Filter: Red or Black

HTP 3” SRI MAF Housing

Available from: HTP 3” SRI MAF Housing
MS6 (Not found), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $154 polished aluminium, +$10 black powder coated; Elbow: 3” standard, 2.5” +$10; Air Filter: Red or Black; Pre-Filter $30

CP-E Nano SRI

See CP-E nViscid below
Available from: CP-E Nano SRI
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $223.60 Silver or Black; Filter: DFlow or SynoilD; Pre-Filter: $16.10

K&N Typhoon SRI

24 HP, mandrel bent aluminium induction tube with heat shield, Million Mile limited warranty
Available from: K&N Typhoon SRI
MS6 (Not found), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $696.18 Red Filter

CorkSport Airbox
MS6

MS3 for Cobb SRI

MS3 Gen2

Available from:
MS6
CorkSport Airbox MS6
MS3 for Cobb SRI
CorkSport Airbox MS3 for Cobb SRI
MS3 Gen2
CorkSport Airbox MS3 Gen2
MS6 (Yes) $98.99, MS3 Gen1 (Yes), MS3 Gen2 (Yes) $99.99

JBR Tru-3.5 Wide Path Full Aluminium / Silicone Intake
Aluminium

Silicone

Available from:
Aluminium
JBR Tru-3.5 Wide Path Full Aluminium Intake
Silicone
JBR Tru-3.5 Wide Path Full Silicone Intake
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $295 TIP: 2.25” Stock, 2.5” BNR, 3” (aluminium only), 4” GT; Silicone: Red, Blue, Black, White; Filter: Black only

CP-E nViscid TIP

(Nano is OEM size and does not require a MAF calibration, but xcelXL is for BT and does): low-restriction design and silicon’s thermal insulation properties, 3-inch cross-sectional flow area throughout. Silicon is 1000 times more heat reflective than aluminium and being steel wire re-enforced, it prevents collapsing under vacuum
Available from:
K04
CP-E nViscid TIP for K04
BT
CP-E nViscid TIP for BT
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $218.40 for K04 or $234 for BT

CorkSport Stage III CAI

10-12% increase in power and torque. enables your engine to take in larger volumes of cold air for better acceleration, includes a one piece of billet aluminium MAF housing with included air straightener to prevent CELs, cleanable dry flow air filter, silicone connectors, T-bolt clamps, mandrel bent aluminium piping, optional TIP
Available from: CorkSport Stage III CAI
MS6 (Not found), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $279.99 with TIP +$70; Silicone, MAF and Filter: Black, Red or Blue; Pipe: Polished or Black Powder; Clamp: Polished or Black;

Injen CAI

15 HP gain, cast multi-stage tuned mid-section for “volumized” airflow throughout the entire power band. The SP Series tuned intake system uses MR technology for optimal gains and safe AFRs.
Available from: Injen CAI
MS6 (Yes), MS3 Gen1 (Not found), MS3 Gen2 (Not found) $293.03 Polished or Black

Cobb Airbox
MS3 Gen1

MS3 Gen 2

Available from:
MS3 Gen1
Cobb Airbox 3 Gen 1
MS3 Gen2
Cobb Airbox 3 Gen 2
MS6 (Not found), MS3 Gen1 (Yes) $199, MS3 Gen2 (Yes) $289

AEM CAI Gunmetal

Info: AEM Cold Air Intake Systems - Performance Air Intakes and Air Filters
Lightweight aircraft 6061 aluminium, mandrel bent, reinforced TIG-welded brackets, complete hardware kit with soft mounts for a guaranteed perfect fit, AEM’s lifetime DRYFLOW Synthetic air filter is 99.4% efficient, filters to one micron, and never needs filter oil, available powder-coated in red, blue or silver, or with a mirror-polished finish, guaranteed for life
Available from: AEM CAI Gunmetal
MS6 (Not found), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $293.99

HKS Racing Suction Reloaded Short Ram Intake SRI

Info: HKS USA
Noticeably louder than stock, quicker spool time, polished intake piping, but must change the air filter every 5,000 miles
Available from: HKS Racing Suction Reloaded Short Ram Intake SRI
MS6 (Not found), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $338.50

ATP 3" MAF Housing Billet Aluminium for DENSO Element

Info: ATP TURBO
Attached directly to the turbo compressor inlet nozzle, which is often the bottleneck of the entire intake system. The OEM provides a pinched and convoluted air path. Specify Garrett 4" inlet or stock turbo 2" inlet, Specify colour: black, red or blue silicone connectors
Available from: ATP 3" MAF Housing Billet Aluminium for DENSO Element
MS6 (Yes), MS3 Gen1 (Not found), MS3 Gen2 (Not found) $95

ATP Turbo SRI

High flow inlet extension including 3" billet aluminium MAF housing, 3" inlet elbow, and 3" open element filter. Bolts onto ATP 3" inlet pipe kit (TIP) to complete a true high flow 3" intake tract. Deletes the restrictive factory air-box and clears the area inside the driver side fender and headlight area to run FMIC pipes in and out. Specify colour: black, red, or blue silicone connectors
Available from: ATP Turbo SRI
MS6 (Not found), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $185 in Black, Blue or Red

JBR Power Path Stage III CAI

14% HP and torque, capable if reducing intake air temperatures up to 15 degrees by drawing cool, fresh, oxygen rich air from deep inside the fender well area, far away from the heat of the engine, mandrel bent, 6061 polished aluminium tube & MAF housing with air straightener, reinforced silicone elbow, SS T-Bolt Clamps, Dry-Flow air filter flows 200% more air, no CELs guarantee
Available from: JBR Power Path Stage III CAI
MS6 (Not found), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $280 MAF / Filter: Black, Blue or Red; Silicone / TIP: plus White

CP-E Xcel CAI
MS6

MS3

CNC machined aluminium MAF housing with airflow straightener improves sensor precision
Available from:
MS6
CP-E Xcel CAI MS6
MS3
CP-E Xcel CAI MS3
MS6 (Yes) $310.96 Silver or Black: Filter: DFlow or SynoilD; Pre-Filter: $16.10, MS3 Gen1 (Yes), MS3 Gen2 (Yes) $269.95

JFB SRI
Available from: can anyone assist with this one? @freakms3; ?
MS6 (), MS3 Gen1 (), MS3 Gen2 () $?

Injen SRI

Gain15 HP and 24lb torque with filter heat shield and a web nano-fibre dry filter
Available from: Injen SRI
MS6 (Not found), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $243.20 Polished or Black

Ultimate Racing SRI

12 WHP, 3.42 ft-lbs torque, high flow cone filter, MAF housing only
Available from: Ultimate Racing SRI
MS6 (Not found), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $150 + optional Black powder coating

Weapon Secret R SRI

Includes heat shield, laminar flow feeds 3X more air than conventional system, 6061 Aluminium on automated CNC mandrel bender and polished, SW1 Air filter features a tuned velocity stack to increase velocity and decrease turbulence, 1 Million Mile Limited Warranty open pore high density re-usable foam
Available from: Weapon Secret R SRI
MS6 (Not found), MS3 Gen1 (Not found), MS3 Gen2 (Yes) $320

Takeda CAI

Designed to place the air filter in the prime location to produce horsepower and torque gains, polished aluminium tube
Available from: Takeda CAI
MS6 (Not found), MS3 Gen1 (Not found), MS3 Gen2 (Yes) $280.50

TurboXS CAI

Mandrel bent 3” diameter aluminium pipes and a custom CNC machined aluminium MAF Sensor Housing, reduces the intake restriction caused by the stock air-box Available from: TurboXS CAI
MS6 (Not found), MS3 Gen1 (Yes), MS3 Gen2 (Not found) $309

DC Sports CAI
MS6

MS3

Info: DC Sports: Cold Air Intake System CAI4101 for Mazda
Washable dry filter (to one micron), funnel top and velocity stack, SS mesh
Available from: Amazon, eBay
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $144.83

Fujita CAI

Polished 6061 T6 aluminium intake tubing, silicone hose with nomex, carbon plated t-bolt clamps, Fujita super flow high performance air filter, TIG welded brackets, vibration mounts, Fujita duffel bag, Fujita hat, NOS energy drinkInfo: FUJITA EUROPE - Air Intake
Available from: Amazon, eBay
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $215.97

Custom Airbox
Temperature drop observed making possible a delay in the FMIC decision

Instructions located at: MS3 normal progression of modifications (stages)
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) <$10 for aluminium sheet

Freek Tunes 3.5” (It’s new, but popularity is expected to rise @jdmadge_mx5; )

AEM dry filter
Available from: Freek Tunes 3.5”
MS6 (Yes), MS3 Gen1 (Yes), MS3 Gen2 (Yes) $299 Coupler: K04, BNR S3, 3”, 4”


DIY Alternative to ATP

Spectre Air Filter

Available from:

3” TIP

3” TIP
3” TIP

[aaronc7]

so, which is best?

good post

[frodaddyweez]

ATP makes a big MAF intake too I believe. Great writeup.

[DISIindahead]

in the end, its all up to the modder, whether its pricing or style

[SofaKingAwesome]

good post. Should add that the CS kit includes the TIP

[sick_role]

nicely done. You may want to add a caveat to the Cobb SF intake that states if you do not upgrade at least your RMM, it is very likely that your bracket will break (unless this has been addressed by a redesign that I'm unaware of).

Good job!

[DISIindahead]

Originally Posted by SofaKingAwesome good post. Should add that the CS kit includes the TIP

Added. Thanks for the heads up.

Originally Posted by sick_role nicely done. You may want to add a caveat to the Cobb SF intake that states if you do not upgrade at least your RMM, it is very likely that your bracket will break (unless this has been addressed by a redesign that I'm unaware of). Good job!

Yeah. Shit happened to me. Thanks for the reminder. Will add a notice.

[Raider]

Great thread! I must note, any BS will not be tolerated in these "mega-resource" threads.

Some quick feedback before reward $ is sent out. Will give a little bit to get response before. Is there anything missing?

***These stickies are to be updated over time, as products come to market. If something comes out, please post here***

[RhoadBlock]

Awesome thread! I'd recommend adding Inlet Pipes too when you get some more time. It's such an easy mod that most people do now cause the stock one is disgusting. TIP is a groovy part of the pre-turbo intake system. And something every bolt-on hero should install.

Edit - and along with the CAIs you should throw a splash shield in there too.
SURE ElementShield - $32.50
CP-E Pre-Filter - $23

Well hell, to save you some time: @DISIindahead
SURE Sidewinder - $179
CP-E Nviscid - $210 (+$15 for BT Flange)
Corksport Inlet Pipe - $99

[DISIindahead]

I start vacation Friday so im sure ill have plently of time to get the TIP added as well. It will be EPIC!

[Raider]

@DISIindahead was given $175,000 MSF Bucks for this thread.

[Ex_WRX_driver]

For the Corksport you could add that they also have an airbox for it.

[SofaKingAwesome]

^^ was just going to add this!
CORKSPORT 2010+ Mazda 3 Air Box for CorkSport SRI

[DISIindahead]

Edit- Added airbox, element shield, prefilter....thanks guys

[MS3-a(sore)ASS-rex]

I suggest making a note about the difference between the cp-e nano being for oem MAF sizes while the xcelXL will need a MAF calibration.

Pretty much something that will tell people nano is for stock turbo and xcelXL is for BT. Don't need any brownies saying "I installed my cpe xcelXL intake and now my car can barely idle and runs like crap"

[Civo93]

Originally Posted by MS3-a(sore)ASS-rex I suggest making a note about the difference between the cp-e nano being for oem MAF sizes while the xcelXL will need a MAF calibration. Pretty much something that will tell people nano is for stock turbo and xcelXL is for BT. Don't need any brownies saying "I installed my cpe xcelXL intake and now my car can barely idle and runs like crap"

What formula did you use to do a maf cal?

[rfinkle2]

Before adding anything, thank you very much for the hard work and personal time dedicated to this thread.

One thing of note:

-The corksport TIP relocates the breather tube coming off of the valve cover from the maf housing to the TIP (optional), much like the newest Mazda fix for the smoking turbo issue.

[DISIindahead]

Edit- added notice

Thanks for the heads up!

Originally Posted by rfinkle2 Before adding anything, thank you very much for the hard work and personal time dedicated to this thread. One thing of note: -The corksport TIP relocates the breather tube coming off of the valve cover from the maf housing to the TIP (optional), much like the newest Mazda fix for the smoking turbo issue.

Thanks man. When I start on the TIP's ill include it. Wow can't believe how good this is going. Cant wait til all the threads are done.

[DISIindahead]

Got some links, pictures and important info for Turbo Inlet Pipes. Still going to wait til Saturday to see if anyone starts a Motor Mount Thread, if not ill be more than happy to start one. Editing will take place as soon as possible, just been busy with work and classes but I should have this thread done by the beginning of next week.

If anyone has more info that they would like to add to this thread, please post a reply and I will edit.

Also if anyone would like to help with the Turbo Inlet Pipe addition, please shoot me a PM with some links/info/pictures.

[RhoadBlock]

Originally Posted by DISIindahead Got some links, pictures and important info for Turbo Inlet Pipes. Still going to wait til Saturday to see if anyone starts a Motor Mount Thread, if not ill be more than happy to start one. Editing will take place as soon as possible, just been busy with work and classes but I should have this thread done by the beginning of next week. If anyone has more info that they would like to add to this thread, please post a reply and I will edit. Also if anyone would like to help with the Turbo Inlet Pipe addition, please shoot me a PM with some links/info/pictures.

I posted links to the 3 main TIPs we have - CP-E, SURE, & Corksport. It was in my 1st post in you r thread. Just link them in yours, snag a pic & the price out of em and tack em on

[uncorked11]

Thank you for your hard work, it looks great!

[DISIindahead]

Edited- Added Turbo Inlet Pipe section..

Hey guys if I missed anything major, let me know and I will edit and add on.

[mituc]

Originally Posted by DISIindahead Hey guys if I missed anything major, let me know and I will edit and add on.

I had a pretty hard time finding the right intake setup on my car. Now I have the Cobb SRI, the CorkSport CAI box for the Cobb SF and an Outerwears pre-filter. I highly recommend both these a accessories.

Here are some pics, maybe you can use them in your post at least to let everybody know that they also have a pre-filter option with other intakes than Injen, CP-E or SURE.



[/quote]

I guess you should also consider listing the MAF housing diameters somewhere for each intake option. This will help people scale their MAF tables a bit just before going on the road for gathering a few logs for a proper MAF calibration.

[RhoadBlock]

Only thing I'd maybe do is move the Element Shield & PreFilter links to the top right after where you mentioned people being scared about sucking up water in a CAI. Makes sense to go there rather than just tacking them at the bottom & not explaining them. Just for the uber-noobers.

Looks awesome bro.

I have the inert urge to state my opinion that a CAI is irrelevant on a turbo car & that the benefits of an SRI outweigh te CAI on our cars lol. But that's for a different thread. Or idk maybe it is for this thread. Someone argue opposite of me so newbs can make their own opinions based upon MSF's viewpoints.

[DISIindahead]

yeah i just noticed that too

like i said, its personal preference for the new guys. Cant favor CAI or SRI due to the makers/vendors possibly getting pissed for favoritism of one or the other, that way we can ,in the end, just leave it up to the buyer. Its up to the new guys to decide based on facts and reviews on which they would want to purchase.



Updated 12/16 - Relocated and added some finesse to the filter cover section

[irishking03]

HKS makes a SRI as well. ONLY downfall is HKS doesnt make shit in the US anymore. Gotta order parts from Japan.

Nice Post though..

[frodaddyweez]

Originally Posted by frodaddyweez ATP makes a big MAF intake too I believe. Great writeup.

No ATP love?

[Raider]

Originally Posted by frodaddyweez No ATP love?

Help OP out and post links and details so it can be copies and pasted in. Come on now.

[DISIindahead]

Originally Posted by frodaddyweez No ATP love?

I got you homie. I found it both for the MS3 and MS6. Im headed to a meet in like 20 so ill have to update in the morning.

[frodaddyweez]

Originally Posted by DISIindahead I got you homie. I found it both for the MS3 and MS6. Im headed to a meet in like 20 so ill have to update in the morning.

Cool. Didn't mean to sound impatient or anything. More options is always mo.betta. atpturbo.com I would look more but working retail during the holidays sucks up all my freetime

[DISIindahead]

no offense taken bro, i appreciate the info..that's what i need, is for people to help me find info and keep this thread updated.


UPDATED 12/21: Addition of ATP Intakes and Turbo Inlet Pipes

[DISIindahead]

ADDED: Outerwears pre filter and some adjusting

[JTMS3]

not sure if the AMSoil filter was mentioned already, but it fits Cobb SRI. Not CONFIDENT on SURE, CS and CPE or any otherl SRIs.

AMS air filter# EAAU4560 Pre-filter# EAPF11

LMK if pics are needed.

[Ferg]

@codyb154

[deptstower]

this is great info -- def will help me w/ my purchases in t he near future

[rednofive]

For CAI's, you listed Injen and AEM and CP-E.

What about the CAI sold by Mazdaspeed through the dealerships?
I think it lists for $408 - is it just a re-badged AEM or injen or CP-E?

thx

5

[Onestop]

Installed a Injen cold air with the Hydra shield on my 09 speed 3 and was very simple to install took less than 45 minutes. Theres no need to remove tire or front bumper if you lift car properly and support it easy to remove the splash guards from underneath vehicle.

As far as performance gains I can definitely feel a difference in power but not as much as they claim. Went with Injen because of the past good experiences on other vehicles will be installing a TIP next.

[FumUnda]

OOPS

Guess I goofed ... please disregard my porrly placed question.

[SofaKingAwesome]

What a nice little brownie. Carry on.

[Raider]

Remove filter. Clean. Replace. All there is to it.