Rock Auto - What doesn't fit??

[Chimmike]

Let this be the beginning.

I have 2 so far that I need to add. Potentially a third.

[cnyms6]

AC compressor didn't fit

[dale_gribble]

I have found a few times where parts listed for my Speed6 is wrong on Rock Auto because for some dumb reason, a lot of parts were listed to work with 2.3L motor and Mazdaspeed MZR even though this isn't right. I mean, the parts sort of fit, but they are different enough to be a PITA; In other words, the part will fit and not leave you stranded, but its just different enough to cause the OCD in you to flare up. A lot of part manufacturers must have assumed the 2.3L and MZR are basically one in the same and didn't do a lot of research.

Specifically for me, the thermostat and radiator. The thermostat on the 2.3L has a longer neck, by about 1.5" then my MS6. The MS6 neck is shorter to clear the power steering hose. The longer neck does fit and will work, but the power steering hose has to be scooted over a bit. The supposed MS6 drop in radiator from them has different lower mounts and the auto trans cooler hookups. I massaged it to work because I was in a pinch, but I will eventually get my stock radiator repaired and reinstalled.

[LilGator]

Blower motor for MS6 doesn't fit. They list it under "2.3L L4 Turbocharged", but it's definitely not a match.

[TiGraySpeed6]

I'll see if I can look up some of the bad part numbers tomorrow, but last I looked, only one passenger side front cv axle, out of 6 different axles, both pass & drivers side, actually fits the speed6.

I also have the specs, dimensions & such that I'll add to feed the search engines and help folks be able to identify speed6 axles from 2.3 na axles which are much smaller

[jack_hammer]

i bought two rear ABS sensors. they both fit. in fact, they say "fomoco" on them. however, i think one is broken. i'm still working on determining that, though...

[Haltech]

Lol someone in SoCal Nator was just pointing to me about this $63 axle they wanted to buy from them.. I hope they see this thread.

[theschrum]

Rock auto is an awesome site for parts, but I always reference the part number to a regular 2.3l before I purchase from them though. I wouldn't be suprised if 20% of the parts listed for our cars didn't fit.

[TiGraySpeed6]

Rock Auto- MS6 axle listing has been improved, but still not perfect. At least it's better than it was. Only a single CV appears to be incorrect.

I can guarantee that Cardone # 608190 is correct, that one was in my car for a couple of months till the rebuild failed- just lucky there. They're usually not bad. It's reasonably safe to "assume" the rear axles would be right, the application shows '06 & '07 only, and hey, they're rear axles....

The first one in the list is certainly incorrect (MZ8338A), and is used as an example of what to watch out for in the pics below.

The entire list- much shorter than it used to be:


See anything amiss with this application list?


Here's a good application list:





Mazdaspeed6 Front CV Axle specs compared to the N/A 2.3 CV axles:
Dimensions:
The Speed6 axles have a much larger nut, 35mm -vs- 32mm, on the splines/hub side. This is the one I've been using a 36mm socket on, by mistake apparently.

This nut size can also be referred to as M24-1.5 on the Speed6, and as M22-1.5 for the smaller NA axle.

Spline section diameter on the speed6 is 32.5mm, and is only 29mm on the NA axle.

Passenger side is also longer for the Normal 6 2.3, since there is no PTO to deal with
- top is the Speed6, bottom is normal 6 passenger side

[SleeperHatch]

Originally Posted by Haltech Lol someone in SoCal Nator was just pointing to me about this $63 axle they wanted to buy from them.. I hope they see this thread.

Yes I see this thread lol. I ended up just buying a OEM axel

[DashingDomin8r]

Exedy Clutch kit doesnt fit.

[lopezsr20]

Does anyone know if the ball joint moog MDBJ4869 they offer for the speed fits?
Or the DEEZA Part # MDH201—

[MazdaSpeedster]

I ordered a cabin air filter last week for my speed 6. I received it today and it did not fit.

[TiGraySpeed6]

What's the part number for the filter which doesn't fit?

[802MS3]

Strut mount kit for the 3 -

Mevotech MS76201 does not come with the strut boot and bump stop, even though it shows both of those in the pictures.

More Information for MEVOTECH MS76201
Details

[spd6demon]

The shaft pivot seal doesn't fit, too big in diameter. I just re-used the old seal but took the spring ring (or whatever its called) out of the new seal and put it in the old one. Been about two weeks and no leaks

[TiGraySpeed6]

Can you post the part number you ordered from RA, or any other details?

Knowing RA, they have some that do fit & some that don't so any details you can provide on what didn't work would be great!

[spd6demon]

Originally Posted by TiGraySpeed6 Can you post the part number you ordered from RA, or any other details? Knowing RA, they have some that do fit & some that don't so any details you can provide on what didn't work would be great!

Part # 221620

There was only one shift shaft seal that came up for the 06' ms6. The seal didnt fit no matter how hard I tried. Seal is slightly too big for housing. Also the new seal wasnt as thick as OEM

[Mandinca]

Originally Posted by spd6demon Part # 221620 There was only one shift shaft seal that came up for the 06' ms6. The seal didnt fit no matter how hard I tried. Seal is slightly too big for housing. Also the new seal wasnt as thick as OEM

For what the OEM costs why didn't you go to Mazda ?

The radiator doesn't fit. The brackets for the fans are all wrong and one of the hose fittings on top is different. It would be nice if it did fit since RA's is $119 and the only other place I could find one was OEM at $350

I also bought a PCV valve from them and the jury is still out on its functionality.

[soul.survivor]

Fel-pro donut exhaust gasket fits but isn't thick enough to make a seal.

[spd6demon]

Originally Posted by Mandinca For what the OEM costs why didn't you go to Mazda ?

My friend actually ordered it for me. Didn't think rock auto's would be different. Guessed wrong lol.

[Rcimp]

I ordered the LUK clutch kit and it fit fine, I also ordered two axles that fit fine to. I ordered two front bearings with hubs and they did not fit.

Bearing with Hub: PRECISION AUTOMOTIVE 513211 - Did not fit.
Clutch Kit: LUK 10064 - Fit
Axle: EMPI 803952 - Fit
Axle: EMPI 803957 - Fit
Clutch Slave Cyl: WAGNER SC143568 - Fit

[season_of_ages]

Radiator was mentioned. Of course, this will include the drain plug. Thread is too small to fit oem radiator

Sent from my SM-N900T using Tapatalk

[madspd6]

Originally Posted by Rcimp I ordered the LUK clutch kit and it fit fine, I also ordered two axles that fit fine to. I ordered two front bearings with hubs and they did not fit. Bearing with Hub: PRECISION AUTOMOTIVE 513211 - Did not fit. Clutch Kit: LUK 10064 - Fit Axle: EMPI 803952 - Fit Axle: EMPI 803957 - Fit Clutch Slave Cyl: WAGNER SC143568 - Fit

The one EMPI Drivers side front axle #803967 for the speed 6 fits fine too as i have it.
I also called EMPI and about 5 months ago they were working on tooling for the passanger side, guy said new tooling takes between 5-6 months to perfect.

[arias valentia]

I got the engine gasket set, 4 exhaust valves and a pcv valve from them and I havnt had any issues except a minor seaping around the valve cover that I attribute more to the some rusty (+1 missing/snapped) cover bolts.

So far I guess i was lucky

Anyone know about the rack and pinion boots?

[maddocx240]

Has anyone ever tried the oxygen sensors for the speed 6? I might need one and wanted to know if they are the right part.

[twiztdspeed]

Ngk 02 sensors should be ok but the dorman intake manifold runner control or ebcs has the wrong male pluge

[Turbo_Steve]

The ngk/ntk o2 sensor part number 24357 worked perfectly for my 08 speed 3.

They list part number 24354 for the speed 6. I am not sure if the connectors are different between the 2 cars but this is probably why it has a different part number. If it is pictured with the heat shield it should be the one you want.